Porsche 914/4 Specialized Tools - Porsche
Click on the thumbnail photos below for
larger images
There are many additional tools for the
Porsche 914/6 cars and Sportomatic transaxles
which are not included here because they do not apply to the Porsche 914/4.
Photos and information shown below are from:
the factory Porsche 914 repair manual,
the 1998 Porsche Specialized Tools catalog,
Clymers and Haynes manuals and a
few other sources.
Some of the tools are no longer available
(NLA).
Available tools may be obtained directly through
Porsche dealers
and tools with an ‘X’ in the catalog page order number may be available at
Baum Tools Unlimited.
|
Category |
Tool ID |
Description |
Tool Purpose |
Image |
Catalog Page |
Tool in Use |
|
Engine |
P 2a |
Piston pin mandrel |
Removes piston wrist pins (See also Tool VW 207c) |
|
|
|
|
Engine |
P 8a |
Piston ring compressor |
Compresses piston rings
for installation (See also Tool VW 123d) |
|
|
|
|
Engine |
P 10b |
Valve spring gauge |
(914/6-only tool?) |
|
|
|
|
Brakes |
P 30a |
Puller |
Removes brake discs |
|
|
|
|
Transaxle |
P 37 |
Drive shaft lock plate |
Holds transaxle input shaft
while removing hex nut |
|
|
|
|
Transaxle |
P 66a |
Puller |
Removes bushings |
|
|
|
|
Transaxle |
P 69 |
Stub axle gauge |
Installs bushings in
transaxle housing |
|
|
|
|
Engine |
P 74 |
Flat blade driver |
Installs and removes wide slotted oil pressure relief valve cover |
|
Baum Tools |
|
|
Brakes |
P 83 |
Spreader |
Retracts brake caliper pistons |
|
|
|
|
Brakes |
P 84 |
Piston gauge |
Rear brake piston venting
clearance gauge |
|
|
|
|
Brakes |
P 86 |
Extractor hook |
Removes brake pads |
|
|
|
|
Brakes |
P 87 |
Dial gauge holder (Mount only, no gauge) |
With dial gauge, measures
brake disc run-out |
|
|
|
|
Brakes |
P 88 |
Torx head wrenches 6mm, 8mm |
Removes and reinstalls brake
caliper bolts (Is this for 914/6?) |
|
|
|
|
Engine |
P 201 |
Engine bench mount |
Heavy-duty engine or transaxle mount (Use with VW 313) |
|
|
|
|
Engine |
P 206 |
Valve guide gauge |
Measures valve guides |
|
|
|
|
Engine |
P 209 |
Holder |
Holds crankshaft while installing connecting rods (Is this for 914/6?) |
|
|
|
|
Engine |
P 215 |
Crankshaft oil seal installer (Rear) |
Installs crankshaft oil
seal at flywheel (See also Tool VW 191) |
|
|
|
|
Transaxle |
P 252 |
Hex socket, 32mm |
Assembles gear stack on
drive shaft |
|
|
|
|
Transaxle |
P 253 |
Press plate |
Removes gear stack at
intermediate plate (See also Tool P 353) |
|
|
|
|
Transaxle |
P 254 |
Driver thrust pieces (3 parts) |
For installing transaxle
bearings |
|
|
|
|
Transaxle |
P 255 |
Guide sleeve |
